Page 1 of 2
Keg design
Posted:
Wed Nov 11, 2015 5:01 pm
by CyBaThUg
I have a spare 50 ltr keg lying around was going to weld the fittings from a cornelias keg on to it so I had a bigger keg with more beer in it has anyone done this or will it not work
Re: Keg design
Posted:
Wed Nov 11, 2015 5:09 pm
by 1 2many
It will work fine but I think your Co2 consumption might rise. :-B
Re: Keg design
Posted:
Wed Nov 11, 2015 6:21 pm
by CyBaThUg
Yeah but so will alcohol consumption bahahaha
Re: Keg design
Posted:
Wed Nov 11, 2015 7:18 pm
by sp0rk
MUCH easier method, grab a pair of these and fit them to the standard coupler for that keg
http://www.ebay.com.au/itm/Keg-King-Bal ... Sw9N1VhlGO
Re: Keg design
Posted:
Wed Nov 11, 2015 11:44 pm
by mudsta
Re: Keg design
Posted:
Fri Nov 13, 2015 4:00 pm
by CyBaThUg
I removed the spear and threw it out a while back so I'm not sure what u mean by placing one of those will help as stated that's wat I was doing :think:
Re: Keg design
Posted:
Fri Nov 13, 2015 7:26 pm
by mudsta
If you don't have the spear anymore then the coupler idea with corny fittings won't work
:handgestures-thumbdown:
Re: Keg design
Posted:
Fri Nov 13, 2015 8:06 pm
by 1 2many
mudsta wrote:If you don't have the spear anymore then the coupler idea with corny fittings won't work
:handgestures-thumbdown:
Good point, but that shouldn't be to hard to sort out. just need some small gauge staino tube to connect to the fitting. :handgestures-thumbupleft:
Re: Keg design
Posted:
Mon Nov 07, 2016 6:36 pm
by CyBaThUg
This idea got shelved for a while just to be clear the connection and spear from the keg is gone so it's just an open hole does this coupler screw into the thread or press into the fitting which is gone
Re: Keg design
Posted:
Mon Nov 07, 2016 6:57 pm
by Carbonator
With no Spear or Dip Tube, you will have to weld the Corny outlet fitting onto the vessel at a low point, above the sediment high tide line (if you get it in your keg). The CO2 fitting can go up top and you will need to create some type of filling method that won't cause the beer to foam-up when filling it. You will need to plate the hole you created, fittings could go on that, but you will need a Dip Tube in one of them.
Re: Keg design
Posted:
Mon Nov 07, 2016 6:58 pm
by Carbonator
CyBaThUg wrote:This idea got shelved for a while just to be clear the connection and spear from the keg is gone so it's just an open hole does this coupler screw into the thread or press into the fitting which is gone
Those fitting mentioned above need Keg Stumps to screw onto.
Re: Keg design
Posted:
Mon Nov 07, 2016 7:02 pm
by CyBaThUg
Might b easier just to weld the spear and fitting on a blank and use a tri lover clamp and weld the other fitting on top of the keg
Re: Keg design
Posted:
Mon Nov 07, 2016 7:03 pm
by CyBaThUg
That way I can remove the blank and use that as the fill port
Re: Keg design
Posted:
Mon Nov 07, 2016 8:14 pm
by Carbonator
Or easier to find another keg and get on ebay and look for a Keg Coupler
Re: Keg design
Posted:
Mon Nov 07, 2016 8:33 pm
by sp0rk
Carbonator wrote:Or easier to find another keg and get on ebay and look for a Keg Coupler
:text-+1:
Don't fuck about with pressure vessels
Do it the right way, with a new keg
Re: Keg design
Posted:
Fri Nov 11, 2016 12:07 pm
by CyBaThUg
I weld vessels for a living and how would u refill one without removing the spear
Re: Keg design
Posted:
Fri Nov 11, 2016 12:14 pm
by Aussiedownunder01
CyBaThUg wrote:I weld vessels for a living and how would u refill one without removing the spear
Same way cub does with a keg coupler send beer down the liquid line and off gas it by the gas line
Over time I have transferred dozens of kegs
Re: Keg design
Posted:
Fri Nov 11, 2016 1:54 pm
by CyBaThUg
Never seen it done so wouldn't know how to pump beer down the line or even wash the keg out after each beer
Re: Keg design
Posted:
Fri Nov 11, 2016 2:20 pm
by sp0rk
CyBaThUg wrote:Never seen it done so wouldn't know how to pump beer down the line or even wash the keg out after each beer
The spear has holes at the top just below the coupler, where the gas comes in, so usually cleaning solution is sprayed at high pressure through the gas inlet, then pumped up out of the liquid out after soaking for a while.
Then rinse and a small amount of santiser would be added and swirled about to coat all surfaces before being drained
To fill beer in, you just purge the keg with CO2, then hook the beer coming in to the beer out line, and vent the CO2 before allowing the beer to come in
Re: Keg design
Posted:
Fri Nov 11, 2016 2:51 pm
by mudsta
To wash a keg they are turned upside down then a coupler is fitted.
Be sure to remove the beer one way valve in the coupler...
Also vent the gas outlet to your cleaning solution tank
Cleaning solution is then pumped into the beer coupler up the keg spear.
The solution sprays over the entire keg internally and then comes out the gas post.
Repeat for rinse and sanitizer