Page 2 of 2

Re: 2.5" LM/VM combo build

PostPosted: Fri May 20, 2011 7:25 pm
by R-sole
You've already got a crack. I can see it to the right of screen.

Re: 2.5" LM/VM combo build

PostPosted: Fri May 20, 2011 7:33 pm
by Kimbo
Mmmmmm!
Bless her little hole :twisted:

Re: 2.5" LM/VM combo build

PostPosted: Fri May 27, 2011 9:28 pm
by Kimbo
Hi Guys,
i'm going to do my first spirit run with this beast tomorow.
Any Tips? do i run it the same as when I did my stripping runs or do i close the take off valve a bit and let the piss come out a little slower?

Re: 2.5" LM/VM combo build

PostPosted: Fri May 27, 2011 9:49 pm
by MacStill
You're going to have to close the valves right of for a while after it's boiled to equalise the column, then pull foreshots and heads via the LM until your into hearts, then you close LM, equalise again before opening VM valve..... it takes a few runs to get the hang of doing a full on spirit run ;)

On HD you'll want to read the couple of threads on running LM and VM stills, the threads are in the reading lounge there.

Good luck :)

edit: First time I ran my old vm/lm I printed those two topics and kept em with me while running the still ;)

If your doing a full keg? have a nice "day" :lol:

Re: 2.5" LM/VM combo build

PostPosted: Fri May 27, 2011 10:02 pm
by Kimbo
Sorry mate, i should have been clearer. :oops:
I will be doing a spirit run of my UJSSM ,5L of low wines ( not neutral which i think you assumed :D )
I assume that I still need to run in Pot still mode?
only slower? :D

Re: 2.5" LM/VM combo build

PostPosted: Fri May 27, 2011 10:22 pm
by MacStill
Ah ok, yeah bring her up to the boil and back the heat off to a nice steady stream, dont push the heat to hard or you'll smear your cuts ;)

Re: 2.5" LM/VM combo build

PostPosted: Sat Jun 25, 2011 6:20 pm
by Kimbo
I done my first Neutral run today, this thing stayed a constant 78 deg and pulled a litre @ 95% in an hour :D
I'm still learning to drive this Mo Fo, but so far i'm impressed :mrgreen:

Re: 2.5" LM/VM combo build

PostPosted: Sat Jun 25, 2011 7:44 pm
by Heffers
Gotta be happy with that mate, well done Kimbo

Cheers, Heffers

Re: 2.5" LM/VM combo build

PostPosted: Sat Jun 25, 2011 7:53 pm
by MacStill
Once you get her dialed in right you'll be taking about 1.5 to 1.7 liters per hour ;)

It's going to be tough tho with the valve on your take off though, you really do need a needle valve on your LM take off to get it fine tuned

It's a great rig for getting neutrals :mrgreen:

Re: 2.5" LM/VM combo build

PostPosted: Sat Jun 25, 2011 7:56 pm
by Kimbo
Thanks mate,
very bloody happy, not too bad for a first effort.
we'll see what happens when i learn to dial it in ;)

Re: 2.5" LM/VM combo build

PostPosted: Sat Jun 25, 2011 8:00 pm
by Kimbo
Cheers Mac,
the valve aint too bad, we,ll see maybe later down the track ;)
at the moment i'ts mainly used as a pot still (with good results)
i recon it's a great all rounder, easy to build and easier to use. totally wrapped

Re: 2.5" LM/VM combo build

PostPosted: Wed Aug 17, 2011 9:59 pm
by Kimbo
Here you go czedd,

the finished product.JPG

close up of the LM,VM.JPG